For those that want to see the DRL/Turn signal bumper duct lighting. Glossy black is the surround of the light just like the duct covers on my 25 Calligraphy. The red wire goes to the wire connected to pin 5 on the headlight harness. Yellow turn wire goes to the wire connected to pin 7 which is the side repeater + circuit. Black wire to the wire connected to pin 9 which is the ground for the headlight/turn assembly. The pins and connectors at the headlight/turn assemblies are identical for left and right.The lights draw about 400 milliamps on my test meter. A very low power draw to operate these. The actual light units protrude from the bumper about 8mm. The old "ducts" that these lights replace are a snap fit into the bumper. They are tightly snapped in with retaining tabs. You need to work from 1/3 way down on the side opposite the duct opening it has 3 tabs. Protect the paint with painters tape. Use a thin plastic pry/spudger tool to start with. Once the tool is in, use a larger pry tool in the opening working your way up. Once you get the first tab released and have room, use your fingers to pull outward, working your way around. The outboard tabs where the duct opening is will be like a hinge so open the duct cover like a door and pull outward at the same time. There is no need to disassemble the bumper at all. Just use proper tools to fit and pry the duct cover out. I usually recommend putting painters tape around the duct cover to prevent marring/scratching the bumper paint.
impaladb
For those that want to see the DRL/Turn signal bumper duct lighting. Glossy black is the surround of the light just like the duct covers on my 25 Calligraphy. The red wire goes to the wire connected to pin 5 on the headlight harness. Yellow turn wire goes to the wire connected to pin 7 which is the side repeater + circuit. Black wire to the wire connected to pin 9 which is the ground for the headlight/turn assembly. The pins and connectors at the headlight/turn assemblies are identical for left and right.The lights draw about 400 milliamps on my test meter. A very low power draw to operate these. The actual light units protrude from the bumper about 8mm. The old "ducts" that these lights replace are a snap fit into the bumper. They are tightly snapped in with retaining tabs. You need to work from 1/3 way down on the side opposite the duct opening it has 3 tabs. Protect the paint with painters tape. Use a thin plastic pry/spudger tool to start with. Once the tool is in, use a larger pry tool in the opening working your way up. Once you get the first tab released and have room, use your fingers to pull outward, working your way around. The outboard tabs where the duct opening is will be like a hinge so open the duct cover like a door and pull outward at the same time. There is no need to disassemble the bumper at all. Just use proper tools to fit and pry the duct cover out. I usually recommend putting painters tape around the duct cover to prevent marring/scratching the bumper paint.
Awe man! I really like that. Maybe I need to bring you my vehicle and just pay you to instal this on mine. I don't have the confidence to be able to pull this off. You don't reside close to Maryland do you 
Wow! Another one done. Looks really good. How long did it take you to install these? I want them but I don't have the confidence to do them myself so if I purchase them, I will purchase them and find a shop to install or luck up and fine a SF owner near me that has installed them and will install for me LOL.
Well for 2027 the taillights are changing design. They will be vertical and not the dogbone look. The front H headlight style is also changing.
-
?
-
?
-
?
-
?
-
?
-
?
-
?
-
?
-
?
-
?
-
?
-
?
-
?
-
?
-
?
-
?
-
?
-
?
-
?
-
?
